Your Position: Home > Blog > Choosing Between A2L and A3 Refrigerants Under EN 378

Choosing Between A2L and A3 Refrigerants Under EN 378

Release Time: 2026-10-23
Read: 61
Share:

Introduction

Against the backdrop of carbon neutrality, low-GWP (low global warming potential) refrigerants are rapidly replacing conventional options across the heating, ventilation, air conditioning and refrigeration (HVAC-R) industry. Names like R32, R454B and R290 are becoming increasingly familiar, yet many engineers still struggle with one question: what do these refrigerants mean for safety, system design and compliance?

The answer lies in two classification systems. Under ISO 817 and the EU standard EN 378, refrigerants are graded by both toxicity and flammability. R32 and R454B belong to the A2L class (mildly flammable), while R290 (propane) and R600a (isobutane) belong to the A3 class (highly flammable). Although both are lower-GWP alternatives, they are handled very differently under EN 378 — the core safety standard for heat pumps and refrigeration systems across the European Union.

EN 378 directly governs the maximum refrigerant charge, installation requirements, ventilation design and electrical protection for every system that uses flammable refrigerants. And because flammable refrigerants must be controlled with exceptional care, the control strategy behind the expansion valve and the safety interlocks around it become just as important as the refrigerant choice itself.

This article explains A2L and A3 in plain language, walks through the EN 378 framework that governs them, and discusses how a well-designed electronic expansion valve (EXV) controller can help your project meet EN 378 compliance while going to market at scale.

What Is EN 378?

EN 378, whose full title is Refrigerating systems and heat pumps — Safety and environmental requirements, is the umbrella safety standard for HVAC, heat pumps, cold storage and commercial refrigeration equipment within the European Union.

Think of it as the safety rulebook for flammable refrigerants. At its core, it answers four practical questions for every installation:

  • How much refrigerant can I charge into a given room or space?
  • What ventilation is required?
  • Does the electrical equipment need to be explosion-proof?
  • How should leak protection and mitigation be implemented?

The most widely used part of the standard is Annex C, which provides the calculation method for the maximum refrigerant charge (Mmax). This is the formula that dictates where the line between acceptable and over-the-limit falls for A2L and A3 refrigerants alike. If your charge exceeds Mmax for the occupied space, you must either reduce the charge, improve ventilation, or add mitigation measures such as leak detection and forced ventilation.

The classification logic itself comes from ISO 817, which grades refrigerants along two independent axes — toxicity and flammability:

  • Toxicity: Class A means low toxicity; Class B means higher toxicity (for example, ammonia, R717, is a B2L refrigerant).
  • Flammability: Class 1 means no flame propagation; Class 2L means mildly flammable with a low burning velocity; Class 3 means highly flammable.

In daily project work, the classes you will most often encounter are A1 (non-flammable, e.g. R410A, R134a, CO₂/R744), A2L (mildly flammable, e.g. R32, R1234yf, R454B, R455A) and A3 (highly flammable hydrocarbons, e.g. R290, R600a, R1270).

The Broader Regulatory Context: Why This Matters Now

EN 378 does not exist in a vacuum. It sits within a wider EU regulatory landscape — most notably the F-Gas Regulation — which has been aggressively phasing down high-GWP hydrofluorocarbons (HFCs). As the F-Gas phase-down tightens year after year, OEMs are being pushed toward lower-GWP alternatives, and many of those alternatives happen to be flammable.

This is precisely why A2L and A3 refrigerants are no longer a niche topic. What used to be the exclusive concern of specialized hydrocarbon refrigeration now applies to mainstream air-source heat pumps, chillers and commercial refrigeration. Understanding how EN 378 treats these two classes — and what the charge limits actually mean in practice — has become a core competence for any engineer or contractor working in the EU market.

A2L: Mildly Flammable — The Mainstream Choice for Heat Pumps Today

Definition: A2L refrigerants are low-toxicity and mildly flammable, with a burning velocity of less than 10 cm/s. They burn slowly and do not easily sustain rapid flame propagation.

Common refrigerants: R32, R1234yf, R454B, R455A.

An intuitive analogy: An A2L refrigerant behaves a little like a slow-burning fuse. It requires a relatively high ignition energy to light, and even when ignited, the flame develops gradually and gently. This low burning velocity is the defining safety property of the class — it is exactly what allows A2L refrigerants to be used in far larger charges than A3 under the same space and ventilation conditions.

How EN 378 Treats A2L

Because the burning velocity is low, EN 378 grants A2L refrigerants significantly more headroom in charge quantity:

  • More relaxed charge limits. Indoor units can be charged at kilogram scale — often tens of times higher than the equivalent A3 charge in the same room.
  • Many applications avoid explosion-proof electrical equipment. After a proper risk assessment, adequate leak detection and ventilation, many commercial heat pumps, central air conditioners and chillers running on A2L do not require ATEX-rated, explosion-proof enclosures. This keeps cost and complexity manageable.

But this does not mean zero risk. If a leak is left to accumulate, the concentration can still reach the flammable range, and the mixture will burn when exposed to an ignition source such as an open flame or a hot surface. Stable system control, reliable leak detection, proper installation and disciplined maintenance remain essential. The safety of an A2L system is an engineered outcome, not a guarantee of the refrigerant itself.

A3: Highly Flammable — Extremely Environmentally Friendly but Strictly Controlled

Definition: A3 refrigerants are low-toxicity but highly flammable, with fast flame propagation and a lower flammability limit (LFL) that is reached far more easily.

Common refrigerants: R290 (propane), R600a (isobutane), R1270 (propylene).

An intuitive analogy: A3 refrigerants belong to the same family as domestic LPG. A small leak, a spark from static electricity, or a tiny hot spot can quickly trigger a fast flame or even an explosion in a confined space. This is why they demand a fundamentally different level of discipline in design and installation.

How EN 378 Treats A3

The contrast with A2L is stark:

  • Charge limits are extremely strict. In many indoor scenarios, the allowable charge is limited to a few tens of grams up to roughly 100–150 grams. For larger systems, dedicated outdoor installation, non-occupied zones, or ventilation-based mitigation is required to justify a higher charge.
  • Numerous installation restrictions. Confined spaces, basements, and service trenches are heavily restricted. Most applications require explosion-proof electrical equipment, ATEX zoned classification, forced ventilation, and leak-detection interlocks that trip the system and purge the space.

The trade-off: A3 hydrocarbons have a GWP of nearly zero and negligible environmental impact, which is why they are promoted as natural refrigerants. The downside is the substantially higher safety burden. As a result, A3 is most practical for small-charge equipment such as commercial display cabinets, small plug-in units and compact refrigerators — not for large centralized systems in occupied spaces.

Side-by-Side: A2L vs A3 Under EN 378

Aspect A2L (R32 / R454B, etc.) A3 (R290 / R600a, etc.)
Flammability class Mildly flammable, low burning velocity Highly flammable, rapid combustion
Ignition difficulty Needs a relatively large ignition energy Static discharge or small spark may ignite
Charge limit Relaxed; can support medium/large heat pump units Very strict; suited to small-charge equipment
Electrical requirement Mostly no explosion-proof needed (after risk assessment) Explosion-proof electrical & ATEX usually required
Typical applications Air-source heat pumps, central A/C, chillers Commercial display cabinets, small refrigeration units
Environmental profile Low-GWP, moderate Near-zero GWP (natural refrigerant)
Leak management Leak detection + ventilation; often enough Leak detection + forced ventilation + interlocks mandatory

Understanding the Charge Limit (Annex C) in Plain Terms

The single most practical number in EN 378 is the maximum refrigerant charge, Mmax, calculated in Annex C. It answers the question: for a given refrigerated space and a given refrigerant, how much charge is safe?

Two parameters dominate the calculation:

  • Room / occupied space volume. Larger spaces dilute a leak more, so they can tolerate a larger charge.
  • Occupancy category. A space that people occupy regularly, and where they could be present during a leak, demands a much lower allowable charge than a non-occupied or outdoor area.

For A3 refrigerants, the allowable charge in an occupied room is typically orders of magnitude smaller than for A2L. This is the practical reason R290 is confined to small equipment: you simply cannot fit a large heat pump charge into an occupied indoor space under the EN 378 Annex C limits without extensive mitigation.

The key takeaway for engineers: do not rely on intuition — always run the Annex C calculation. The difference between compliant and non-compliant is often a matter of a few grams of charge or a few cubic meters of room volume.

Clearing Up the Most Common Misconceptions

Misconception 1: “A2L is safe and harmless, so I can install it anywhere.”

Reality: A2L is still flammable. EN 378 requires you to calculate the maximum charge against the room volume and ventilation conditions. Exceeding that limit is a genuine hazard. Leak detection, proper installation and disciplined maintenance are non-negotiable.

Misconception 2: “R290 is a natural refrigerant, so it must be the safest option.”

Reality: R290 is outstanding for the environment, but its safety risk is higher, not lower, than A2L. It is perfectly usable — but only in tightly controlled, small-charge scenarios with full explosion protection. Natural describes its environmental origin, not its safety profile.

Misconception 3: “Any flammable refrigerant requires explosion-proof equipment.”

Reality: EN 378 treats the classes differently. A3 almost always requires explosion-proof hardware. But an A2L system, after a proper risk assessment with controlled charge and adequate ventilation, can often be built with conventional electrical equipment — which is a major reason A2L dominates larger commercial equipment.

How to Keep a Flammable-Refrigerant System Stable: The EVD Controller Approach

Regardless of whether you choose A2L or A3, one truth holds: system instability amplifies safety risk. Fluctuating load, loss of superheat control, and abnormal start/stop behavior can all push a flammable-refrigerant system toward dangerous operating conditions. This is exactly the pain point many OEMs hit when switching to low-GWP refrigerants.

Hexing Technology’s EVD series electronic expansion valve controllers are designed natively for A2L and A3 refrigerants, providing stable, reliable refrigerant flow control for EN 378-compliant applications:

  • Pre-loaded multi-refrigerant library. Native support for A2L/A3 refrigerants including R32, R454B and R290, compatible with single- and dual-coil electronic expansion valves from major brands.
  • High-precision superheat control. Under load fluctuations, defrost transitions and extreme high/low temperature conditions, the controller rapidly regulates refrigerant flow to avoid liquid slugging and excessive discharge temperature — reducing the abnormal conditions that can lead to refrigerant leaks.
  • Rich protection and interlock interfaces. Built-in low-superheat protection, MOP/LOP pressure protection, and a reserved leak-alarm signal port that can interface directly with flammable gas detectors. When an alarm triggers, the controller can shut down the system and open ventilation — exactly the kind of interlock EN 378’s safety-management philosophy calls for.

The point is simple: selecting the right refrigerant is only the first step. A stable, controllable electronics platform is what gives a flammable-refrigerant project the confidence to meet EN 378 and scale into serial production.

Final Thoughts

The shift to low-GWP refrigerants is an industry-wide inevitability, and there is no absolute better between A2L and A3:

  • If you need large-capacity heat pumps or central air conditioning, balancing safety, energy efficiency and cost, A2L is the more balanced choice for the current stage.
  • If you pursue maximum decarbonization, have small-capacity equipment, and can implement complete explosion protection and ventilation, A3 hydrocarbon refrigerants are a viable route.

Whatever you choose, the underlying foundation is the EN 378 safety framework. Whether you are an equipment manufacturer, a system integrator or a service technician, understanding refrigerant classification and calculating charge limits correctly — and pairing the refrigerant with a stable, compliant electronic control platform — is the first and most important step toward safe, scalable deployment.

Table of Contents

    Send inquiry Now

    Chat Now
    info@corestartech.com
    +86 13771791973
    +86 13771791973

      X